Search filter

Applications: Assembly and repair (5); Grab adhesives (5); Heating, Ventilation & Air Conditioning (13); Home decoration (35); Industrial Assembly (5); Industrial seamless floors (10); Insulating Glass (4); Labelling (15); Parquet (12); PVC welding (4); Rigid packaging (30); Sealants (7); Self-levelling compounds (14); Soft floor (carpet /PVC) (20); Substrate preparation/Primers (13); Tapes and Labels (12); Tiling (10); Wall adhesives (9); Waterproofing coatings (9); Wood working (15)
Brands: Ardal (14); Bostik (137); Eponal (14); Laybond (2); Novaflex (4); Quelyd (17); Roxol (10); Sader (13); Tarbicol (4)
Destinations: Floors (72); Walls (21)
Specific characteristics: Environmentally friendly (47); Exterior (21); Heat resistant (7); Ready-to-use (91); Suitable on wet substrate (7); Water resistant (18)
Substrates: Ceramic tiles (31); Paper/cardboard (66); PVC (25)
Segments: Construction (105); Consumer (17); Industry (95)

Saniplas EC

Pipe adhesive, for rigid PVC-U tubes and connections.

Additional Downloads
MSDS
Definition
Open timeTime between the moment the adhesive was applied and the moment it has no more tack (end of possible laying the covering)

Uses

Saniplas EC is suitable for plastic pipe cement assemblies for pressure and discharge lines as well as underground communication lines.
Suitable for unplastied PVC.

Benefits

Rapid cure
Easy spread
Excellent ageing properties
EN 14814 agreement under way

Properties

Physical:

- Colour : translucent
- Specific gravity : approx 0.90 g/cm3 at 20°C
- Viscosity (Brookfield) : 3 000 - 6 000 mPa.s (Spindle 6, 100 rpm at 20°C)
- Application temperature : +5°C to +35°C
- Open time : 2 minutes at +20°C
- Dry content : approx 20%
- Drying time : 1 hour for pipe diameters < 90 mm, others 24 hours

Consumption:

Typical consumtion : 1 Kg of Saniplas EC to assemble 100 units 40 mm diameter

Safety:

IMPORTANT: before embarking on any work involving our Saniplas EC, the separate Product Safety Data Sheet must be studied carefully by those carrying out the work.

Observe good hygiene in use. Avoid skin and eye contact.Highly flammable.

Shelf life:

2 years in a cool ventilated place (max +35°C)

Application

PREPARATION :
Pipe assemblies must be properly prepared :
- Sand down the surface of the parts to be assembled (male end and socket) with sandpaper (never used a file, rasp or sawblade for this purpose)
- Clean the parts to be assembled with a clean cloth or brush moistened with our SOLVANT N°1

GLUING :
Carefully spread a thin uniform layer of Saniplas EC without excess inside the socket and on the complete outer surface of the male end, ending in the lengthwise direction.
When application of the glue is finished, be careful to put down the brush in a clean place.
Since the adhesive dries rapidly, immediately assemble the two parts by pushing them together straight, without any twisting motion.
Eliminate the excess of glue from the outside of the assembly with a clean cloth.
It is necessary in all cases to allow the assembly to dry for 10 minutes before handling to prevent any relative movement between the assembled parts.
Wait minimum for 30 minutes before placing the pipe assembly underground.

REMARKS :
- To prevent excessive volativle solvent evaporation, always tightly close the can or drum between uses.
- Prevent any ingress of water (rainwater or other).
- After drying, a waterpoofing test should be carried out (DTU 60.1)

CLEANING :
SOLVANT N°1

Packaging

Presentation	Bar code	Bostik code
Can - 1 litre(s)	3131360521397	511092